Bongs and college. A natural combination! We at The Blur of Insanity wish to help you enjoy the beauty of bongs!



NEW!! GRAVITY BONG #1

Okay... we got many e-mails about gravity bongs, and many different and bizarre design. We settled on two. The first #1 design being the standard "Gravity Bong." We made it simple but it can be modified in many ways. One potential approach is to put an additional hole in it for either the bowl, or as a place to smoke through. Some add complications you may not wish to undertake. But basically this one works with the least problems maintaining proper suction! Thanks to all who sent e-mails. We printed them out, did tests (which is why the updates were late) and here are our results!


click here or on image for larger images!

WHAT YOU'LL NEED:

Cut the Soda Bottle in half. Fit the Bottom end inside the top half. Take the cap and drill a hole in the top. Fit the stem through the cap and seal in place with caulk or chewing gum. Screw cap back into bottle.

HOW IT WORKS:
This bong works on suction not gravity. But if you haven't been going to classes much you might not know that! Start by compressing the two halves of the bottle together. Then load the bowl. NOTE: If you load the bowl during the compression stage the pot will fly out!!!! Light the dope and pull the two halves apart. This will cause the bottle to fill. NOW... remove the cap, put your mouth over the mouth of the bottle and compress (slide) the halves together. This should force a good amount of smoke into your lungs causing you to pass out on the floor of your dorm.

 

NEW!! GRAVITY BONG #2 (aka "BUCKET-BONG")

This is also called a "bucket-bong" which is, at least, true. In all honesty, gravity has absolutely nothing to do with either of these gravity bongs. From what we can guess the name "Gravity Bong" was generated by someone completely stoned and useless. If the person was straight (or watched "Sports Figures") they would know to call it a "Suction Bong." But whatever you call it, it is an effective mind destroyer, and thus on our pages!


click here or on image for larger images!

WHAT YOU'LL NEED:

Cut the Soda Bottle in half. Discard the Bottom end. Take the cap and drill a hole in the top. Fit the stem through the cap and seal in place with caulk or chewing gum. Screw cap back into bottle.

HOW IT WORKS:
This bong also works on suction and not gravity. Gravity and suction are not the same! Start by filling the bucket with water about 3/4 of the way up. Now push the top half down into the water. Then load the bowl. NOTE: If you load the bowl during the compression stage the pot will fly out!!! NOW- Light the dope and pull the top half up - but not OUT of the water. This will cause the bottle to fill with smoke. NOW... remove the cap, put your mouth over the mouth of the bottle and compress (push) the top half back down into the water. Smoke should rush into your lungs, the walls should melt, and you will likely become useless and believe that suction and gravity are the same.

 

THE WATER-COOLER HOOKAH
(via the Shaolin Bong Squad -they now claim to be the best bong builders!
Sorry Bad Arnold!)


CLICK ON IMAGE OR HERE FOR A LARGER PICTURE!

WHAT YOU'LL NEED:

Drill two holes to fit the clear tubing. Attach hoses. (NOTE: attach as many as you want!) Seal with caulk -let dry overnight. Stick stem through rubber stopper. Fill with water. Place stopper in top. Attach bowl. Destroy lungs!


NEW!! THE CHEAP BONG 2
(the first one was designed ass-backwards - our 3D expert has lowered his dosage of crank - and redesigned the bong so you don't get a mouthful of water!)


CLICK HERE OR IN IMAGE FOR LARGER VIEW

WHAT YOU'LL NEED (this should be around the house):

Take the Soda bottle. Use pen to make hole in side a 1/3 up from the bottom. remove pen guts (so there is a hollow tube). Push into bottle and seal with chewing gum. Take aluminum foil and form bowl with a hollow stem at least 2 inches long (you want to make sure that doesn't melt the plastic pen tube - plastic fumes can kill you, or at least make you VERY sick. Use the pen to wrap the foil around - that will make sure you can pull air through it. Fill with water so that bottom of pen tube is below water. You now own the cheapest bong known to mankind! NOTE: Beware of lighting your hair on fire when you light this thing!


THE DUAL (tm)
design by Bad Arnold
(the best bong builder ever known to mankind)

The smoothest bong ever. Beautiful design!

CLICK ON IMAGE OR HERE FOR A LARGER PICTURE!

WHAT YOU'LL NEED:

Attach hose through the top of the cap into the first cylinder (IMPORTANT: hose end should be ABOVE the water line). The other end of the hose, which goes in the second cylinder,r should be submerged under the water. Make sure the cap on the first cylinder forms a very tight seal!

HOW IT WORKS:
Load the first chamber boiling water and the second chamber with ice water.
Use normally, like a standard cylinder bong.


THE LOW-RENT HOOKAH

A basic hookah if you don't feel like spending over fifty or more for one of those glass jobs.
Easily made and you can also just put on one hose for personal use.

CLICK ON IMAGE OR HERE FOR A LARGER PICTURE!

WHAT YOU'LL NEED:


HOW IT WORKS:

Assemble via the blueprint, then light up and draw through the hoses. Not as efficient as the expensive kind but it works.

Now you can act like turban-wearing Opium lord. A good project for a rainy afternoon.


THE DIRTWEED BONG (aka the BBQ BONG)

We got a suggestion for a bong that went as follows:

From: rastaboy
Date: Wed, 24 Apr 1996 00:27:10 -0400
To: insanity@cloud9.net
Subject: death bong

You call that a bong :) ha! my bowl to my 6 footer is bigger than that thing...here's a good idea for ya take a big piece of pipe, like 3 feet long and stick it into a side of a bar-b-que and throw in a 2 or 3 pounds and close the lid and light up see how you like that...rastaboy

We like it so much we made one!

NOTE: Some people actually thought we were serious and built one!

WHAT YOU'LL NEED:


HOW IT WORKS:
After dinner, when the coals are hot, toss a 1/4 of crappy weed on the grill and close tight. Inhale at will.

Your friends and you will likely be found dead the next morning. Please leave a will leaving everything to The Blur of Insanity! Thank you!


THE STANDARD CYLINDER MODEL

This is a simple one. Basic, works great, and is easy to use!

CLICK ON IMAGE OR HERE FOR A LARGER PICTURE!

WHAT YOU'LL NEED:


HOW IT WORKS:
We think you can figure it out.


THE DEATH BONG

A brutal design. Will even make the most basic cannabis very strong. Be careful!


CLICK ON IMAGE FOR A LARGER PICTURE!

WHAT YOU'LL NEED:


HOW IT WORKS:
Not quite as simple as a standard bong. The carburetor is the big pipe splitting off at 45°. This allows a LARGE amount of smoke to blast into your lungs VERY suddenly! The process is like this.

1. Light up.
2. Start smoking.
3. Close the valve (this cuts off all incoming air).
4. YANK the cord attached to the plastic aerosol top.
This causes a ton of smoke to go into your lungs instantly.

5. Pass out.


MORE DESIGNS IN THE WORKS! Design ideas?
SEND THEM TO US AND WE'LL PUT THEM UP.
That is, unless they really suck. CLICK HERE TO SEND THEM.